26 Aug
2016
26 Aug
'16
1:21 p.m.
> We are facing a problem when using UDPCast in
multicast mode. When I start a transfer from one pc to another, no problem.
> I contacted network-support and they presume it could be a conflict with the VVPR
(Virtual Router Redundancy Protocol) which also uses multicast.
> udp-sender --ttl 1 and udp-receiver --ttl 1 udp-sender --ttl 2 and udp-receiver
--ttl 2 udp-sender --mcast-rdv-address 224.0.0.3 and udp-receiver --mcast-rdv-address
224.0.0.3
> But the problem persists.
If possible, can you please verify what happens when udp-sender transmits at 10%, 20%,
40%, 80%, and/or 100% of the smallest pipe?
--max-bitrate bitrate
--rate-governor module.so:key1=value1,key2=value2
--bw-period seconds
THIS MESSAGE IS FOR THE USE OF THE INTENDED RECIPIENT(S) ONLY AND MAY CONTAIN INFORMATION
THAT IS PRIVILEGED, PROPRIETARY, CONFIDENTIAL, AND/OR EXEMPT FROM DISCLOSURE UNDER ANY
RELEVANT PRIVACY LEGISLATION. No rights to any privilege have been waived. If you are not
the intended recipient, you are hereby notified that any review, retransmission,
dissemination, distribution, copying, conversion to hard copy, taking of action in
reliance on or other use of this communication is strictly prohibited. If you are not the
intended recipient and have received this message in error, please notify me by return
e-mail and delete or destroy all copies of this message.
30 Aug
30 Aug
11:57 a.m.
Hi,
Thankyou for your answer, but I am using UDPCast in windows commandline, there are no
examples included with the windows command-line programs.
Could you be a little bit more specific please?
Can you give me an example how to set these commandline parameters?
Much thanks in advance,
Steve Dubois
-----Oorspronkelijk bericht-----
Van: Brent Kimberley [mailto:Brent.Kimberley@Durham.ca]
Verzonden: vrijdag 26 augustus 2016 15:22
Aan: Dubois Steve
CC: 'udpcast(a)udpcast.linux.lu'
Onderwerp: Problem: UDPCast transfer breaks DHCP leases
> We are facing a problem when using UDPCast in
multicast mode. When I start a transfer from one pc to another, no problem.
> I contacted network-support and they presume it could be a conflict with the VVPR
(Virtual Router Redundancy Protocol) which also uses multicast.
> udp-sender --ttl 1 and udp-receiver --ttl 1 udp-sender --ttl 2 and
> udp-receiver --ttl 2 udp-sender --mcast-rdv-address 224.0.0.3 and udp-receiver
--mcast-rdv-address 224.0.0.3 But the problem persists.
If possible, can you please verify what happens when udp-sender transmits at 10%, 20%,
40%, 80%, and/or 100% of the smallest pipe?
--max-bitrate bitrate
--rate-governor module.so:key1=value1,key2=value2 --bw-period seconds THIS MESSAGE IS FOR
THE USE OF THE INTENDED RECIPIENT(S) ONLY AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED,
PROPRIETARY, CONFIDENTIAL, AND/OR EXEMPT FROM DISCLOSURE UNDER ANY RELEVANT PRIVACY
LEGISLATION. No rights to any privilege have been waived. If you are not the intended
recipient, you are hereby notified that any review, retransmission, dissemination,
distribution, copying, conversion to hard copy, taking of action in reliance on or other
use of this communication is strictly prohibited. If you are not the intended recipient
and have received this message in error, please notify me by return e-mail and delete or
destroy all copies of this message.
2131
days inactive
2135
days old
1 comments
2 participants
participants (2)
-
Brent Kimberley -
Dubois Steve