Sumit, Are you running it from the command prompt ? If you just the run the executable by double-clicking, it will display the help-text and the window will close. Regards, Samar On Sun, May 23, 2010 at 11:03 AM, Sumit Arora <sumit@alldeankenya.com>wrote:

Hi Abe

As soon as I press enter after giving specific command the window for sender or receiver closes.

Thanks and Best Regards.

_______________________________________________________________________

Sumit Arora

size=2 width="100%" align=center tabindex=-1>

*From:* udpcast-bounces@udpcast.linux.lu [mailto: udpcast-bounces@udpcast.linux.lu] *On Behalf Of *Abraham Y. Chen *Sent:* Saturday, May 22, 2010 5:40 PM *To:* Sumit Arora *Cc:* udpcast@udpcast.linux.lu *Subject:* Re: [Udpcast] Using Windows version of UDPcast 201005220726.AYC

Hi, Sumit:

1) Have you simply followed the command line instructions at:

http://udpcast.linux.lu/cmdlinedoc.html

to try a file transfer? They apply to Windows downloaded version just fine. It should get your first foot into the door.

1) I am not a software engineer, but a system engineer with primarily hardware background, in the process of trying to make use of the very beginning part of the this utility for establishing a near real time knowledge database about all active nodes on a network. If you have applications other than what UDPcast basically intends to provide, we can discuss further, perhaps off-line.

Abe (2010-05-22, 07:39) Avinta Communications, Inc. www.Avinta.com

Sumit Arora wrote:

Dear All

First I would like to thank all the developers who has developed this wonderful software for multicasting files.

I am in great need of this software and has downloaded windows version.

Can someone send me the detailed procedure for sending and receiving a particular file using Windows utility?

i tried but as soon as i press enter in window of sender or receiver the window gets closed.

Please assist

Thanks Sumit

------------------------------

_______________________________________________

Udpcast mailing list

Udpcast@udpcast.linux.lu

https://udpcast.linux.lu/cgi-bin/mailman/listinfo/udpcast

_______________________________________________ Udpcast mailing list Udpcast@udpcast.linux.lu https://udpcast.linux.lu/cgi-bin/mailman/listinfo/udpcast

Dear Abraham/Samar Thanks for your response. I am giving this command on command prompt using the file actual file name And now I am getting error as mentioned in snapshot below. Please suggest. Thanks and Best Regards. _______________________________________________________________________ Sumit Arora _____ size=2 width="100%" align=center tabindex=-1> From: Abraham Y. Chen [mailto:AYChen@Avinta.com] Sent: Sunday, May 23, 2010 10:22 PM To: Sumit Arora Cc: Knight Samar; udpcast@udpcast.linux.lu Subject: Re: [Udpcast] Using Windows version of UDPcast 201005231203.AYC Re:201005220726.AYC Hi, Sumit: Just to be double sure, when you run UDPcast programs from Windows' command prompt (or, so called MS-DOS mode), type the two commands referenced in two respective PCs according to what are on the website verbatim, except that the "outfile" part should be replaced with an actual file in the same file folder as the udp-sender. The symptom that you described sounds similar what happened to me during my initial attempts, besides what Knight observed. Without a valid file to handle, these programs may terminate in certain "unexpected" way. Abe (2010-05-23, 12:21) Knight Samar wrote: Sumit, Are you running it from the command prompt ? If you just the run the executable by double-clicking, it will display the help-text and the window will close. Regards, Samar On Sun, May 23, 2010 at 11:03 AM, Sumit Arora <sumit@alldeankenya.com> wrote: Hi Abe As soon as I press enter after giving specific command the window for sender or receiver closes. Thanks and Best Regards. _______________________________________________________________________ Sumit Arora size=2 width="100%" align=center tabindex=-1> From: udpcast-bounces@udpcast.linux.lu [mailto:udpcast-bounces@udpcast.linux.lu] On Behalf Of Abraham Y. Chen Sent: Saturday, May 22, 2010 5:40 PM To: Sumit Arora Cc: udpcast@udpcast.linux.lu Subject: Re: [Udpcast] Using Windows version of UDPcast 201005220726.AYC Hi, Sumit: 1) Have you simply followed the command line instructions at: http://udpcast.linux.lu/cmdlinedoc.html to try a file transfer? They apply to Windows downloaded version just fine. It should get your first foot into the door. 1) I am not a software engineer, but a system engineer with primarily hardware background, in the process of trying to make use of the very beginning part of the this utility for establishing a near real time knowledge database about all active nodes on a network. If you have applications other than what UDPcast basically intends to provide, we can discuss further, perhaps off-line. Abe (2010-05-22, 07:39) Avinta Communications, Inc. www.Avinta.com Sumit Arora wrote: Dear All First I would like to thank all the developers who has developed this wonderful software for multicasting files. I am in great need of this software and has downloaded windows version. Can someone send me the detailed procedure for sending and receiving a particular file using Windows utility? i tried but as soon as i press enter in window of sender or receiver the window gets closed. Please assist Thanks Sumit _____ _______________________________________________ Udpcast mailing list Udpcast@udpcast.linux.lu https://udpcast.linux.lu/cgi-bin/mailman/listinfo/udpcast _______________________________________________ Udpcast mailing list Udpcast@udpcast.linux.lu https://udpcast.linux.lu/cgi-bin/mailman/listinfo/udpcast